Despite the severe demands of today’s drilling industry, downtime, leaks, and mistakes are not an option. That’s why we engineer our premium land and offshore drilling, tank trunk, and fracking oilfield appliion hoses and asselies with cutting-edge technology
The pressure is sometimes stated as ‘head of water’. If the head is given in metres of water, each 1-metre head (3.28 ft) induces 0.1 bar (1.47 psi.) pressure. All formulae for finding the amount of fluid that will flow through a hose at a given time, are approximate.
4 Hydraulic Hose Selection Guide NRP Page Nuers Dash Size and W orking Pressure Industry Part Specifiions No. Construction Hose Fittings -3 -4 -5 -6 -8 -10 -12
05/99 N/AL 9.12.001.03 Metric Tubing and Hose Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifiions given in this document. O/D I/D Maximum working pressure (bar) Minimum bend
The pressure drop in compressed air lines can be calculated with the empirical formula dp = 7.57 q 1.85 L 10 4 / (d 5 p) (1) where dp = pressure drop (kg/cm 2) q = air volume flow at atmospheric conditions (m 3 /min) L = length of pipe (m)
Maximum working pressure 5,000 psi (345 bar). Allows operator to switch from flexible to rigid extension with one hand. Overall length 13 in. (330mm). 1/8 in. NPT(m). For use on hand guns or air-operated grease control valves.
28/4/2020· Valves: Ensure that the safety valves on your air tank are set to at least 10% or 15 psi — whichever is greater — above the operating pressure of the compressor but never higher than the air receiver’s working pressure limit. If using an air compressor in freezing
Vacuum Hose These vacuum hoses have a light and strong design for appliions such as extraction and conveyance in explosion hazard areas, electrostatic discharging, antistatic and other general industrial vacuum appliions. shop now
Technical Data Pressure Ratings, General Reference lowest pressure rated fitting end. For example, a fitting may include one -4 (1/4") male 37 degree tube end and one -6 (3/8'') male pipe end. From the tables below, the rated working pressure for the -4 male 37
How to Measure the Size of your High Pressure Washer Hose Connections: Use Vernier Callipers, a Ruler or Tape Measure Measure across the diameter of the threaded make part of the fitting, including the thread Remeer: 13mm = 1/4" – 14mm – 16.5mm
15m PVC air hose hose length 300psi (20 bar) max. input pressure 1/4" BSP male air inlet/outlet hose connectors Supplied with wall / ceiling mounting bracket 30 reviews A retractable air hose reel that''s ideal for use in workshops, garages, numerous
Thermoplastic Hose and Fittings Parker Parflex Division offers thermoplastic and Feflon® hose products that cover the full range of industrial fluid transfer appliions. Our hoses are available in a wide choice of core tube materials, reinforcement designs, and outer
Hosecraft USA offers every type of food hose and beverage hose. FDA, USDA, 3A all apply to the sanitary hoses. TS2 PTFE SMOOTH BORE BRAIDED HOSE The TS2 SmoothFlex is a smooth bore PTFE hose with stainless steel or polypropylene braid reinforcement that is designed for a wide range of chemical resistant and high purity appliions.
1 1/4" - 10" 10 bar 150 psi-30 C to +80 C-22 F to +176 F General purpose water discharge hose for in-plant water service in general industrial and agricultural appliions. Also suitable for air service. Flexible and easy to handle.
Get the best deals on 1/4 Inch Inside Diameter Hoses & Tubing when you shop the largest online selection at eBay. Free shipping on many items | Browse your favorite
1/4-inch is by far the most common diameter used in pressure washers for around the home. Of the 10 bestselling pressure washer replacement and extension hoses online 8 were 1/4-inch diameter. And 2 were: 3/8-inch is the thickest diameter hose you’ll see
Maximum Working Pressure (psi) Burst Pressure (psi) Weight per Foot (lbs.) 1/4 0 0.42 3.7 90 0.07 1 0.48 1,800 7,233 0.14 2 0.54 2,700 9,100 0.20 3/8 0 0.65 4.0 70 0.15 1 0.71 1,558 6,230 0.25 2 0.77 2,336 9,345 0.36 1/2 0 0.77 4.4 70 0.18 1 0.83 1,186 2 0
1/4 in. x 25 ft. polyurethane air hose with 1/4 in. male NPT swivel end fittings Very good cold weather flexibility Smooth finish does not mar surfaces Light weight for less user fatigue Bend restrictors for increased hose life 300 psi work pressure Blue color
SPIR STAR offers water-blast hoses with a maximum working pressure of up to 4.000 bar (safety factor of 2,5:1). High-Pressure Hydraulics SPIR STAR® thermoplastic high-pressure hoses are developed and produced for high working pressures up to 1.800 bar (safety factor 4:1).
Each constant-working-pressure family has color-coded laylines based on pressure rating and is available with different covers to match appliion requirements. These hoses meet the minimum 1 million cycles required in ISO 18752 Grade D, Type DC and have been tested up to 2 million impulse cycles and at a tighter bend radius than required by the specifiion.
Check the pressure at the tool: Attach a pressure gauge between the end of your hose and your air tool to confirm whether the air pressure is at the maximum recommended pressure. Each air compressor design is different, and some systems can lose pressure before the air reaches the tool.
Pressure: 10,5 bar / 150 psi H0661 - COUGAR Corrugated Hose Tube: CPE Reinforcement: 2-ply fiber with helical wire Cover: EPDM Temp: -43 C to +135 C, (-45 F to +275 F) Pressure: 12,1 bar / 175 psi H8359 - PANTHER Chemical Hose Tube: XLPE 2-ply
For professionals and homeowners alike, your pressure washer hoses will eventually deteriorate and need to be replaced. Whether you need a replacement hose, or you are a professional and need extra length for tough jobs, you can find the best power washer
Style Safety Air Gun Tip Type Safety Nozzle Maximum Working Pressure (psi) 230 Thread Size on Inlet 1/4 NPT Tube Length (Inch) 4 Contents Tire Gauge PSC …
If you have 8 bar coming out of your compressor, but the pressure reaching your tool is only 6.5 bar - you’re experiencing pressure drop. Air hoses are one of the primary causes of pressure loss in a system and can cause an air tool to run ineffectively.
Meaning of Bar All air compressors force air into a confined space where it is stored ready for use. When the user demands the air to drive, for example a tool, the storage unit will open a valve and the air under pressure will flow down the output hose or other connector.
Double Jacketed Super Strong Premium Construction Hose. Designed and manufactured for Fire Brigade and Heavy Industrial Fire Fighting appliions where high water pressure is required Jackets are made of 100% polyester yarns, seamless woven on circular